• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix door Hinge a Loose Door Hinge

Most homeowners can fix a loose hinge. If the holes for screws are shattered and do not hold screws, you may require wood glue and dowels in order to reinstall the door hinge.

Before you do that, however you should clean off any surface rust. This will help the dowels stay in place and give them a solid base to hold onto.

Eliminating the Hinges

A lot of door hinges are able to be removed, making it easier to move the door from one side to another or to remove the entire door off of the frame if need be. Anyone who is patient can remove the hinges, but you need to know what to do.

If the hinges have been painted, you'll need to remove it before you attempt to remove the pins. If you do not, the paint may be smashed off and scratch your door when you try to lift it. To break the seal put the hinges in an stainless steel pan and fill the pan with water until the hinges are completely submerged. The hinges should remain in the pan for approximately 30 minutes. The heat of the water will soften the paint making it easier to take off.

After the pins have been loosened, remove the hinges and frame from the door. It is possible to use a regular screwdriver, but a magnetic screwdriver is recommended for this project. This type of screwdriver has been specially designed to pick up metal screws and will assist you in getting the task accomplished much faster.

It is a good idea to spray some lubricant on the hinges before attempting to remove them. A simple lubricant can make the process go by more quickly and help you remove the pins and screws. You can find this type of lubricant at a variety of hardware and home improvement stores.

The number of hinges needed will also vary depending on what type of door you have and how it is set up. Solid-cored and heavier doors will require more hinges, whereas lighter and hollow-cored doors may only require two or three hinges.

It is also crucial to be aware of the various kinds of hinges so you can determine which ones will best suit your needs. The hinges on the exterior are designed to hold the weight of a door, while interior hinges must be able to handle heavier loads.

Reattaching the Hinges

Sometimes, a hinge on a door will get looser and eventually begin to hang crookedly or sag. It can be a big problem, but the fix is usually easy. A simple retightening will usually solve the issue. However, if the screw holes are stripped out, it can be more difficult. A wood dowel can be used to tighten the holes again.

Begin by drilling the old hole using a drill close to the new screw size (normally 3/8"). Then, use a wood glue as well as dowels made of wood to fill the hole. The dowel should be cut to a length that is the same as the screw to ensure a secure fit. Reinstall the screw and tighten it until you are satisfied with the degree of tightness. If the door does not stop bind up, you can insert another dowel to the gap. Repeat the process. Close the door slowly after each adjustment to ensure the perimeter clearances are in order.

You could also use a wood plug instead of the dowel. This is also a viable option, but may take a bit longer to install. Simply whittle a piece of wood that is the proper size to ensure a secure fit, and then insert it into the hole. If you don't have a woodworking tool You can also try using toothpicks or wooden matches as well.

After you have reinstalled the new screw and countersink the screw, you can use a countersink tool to make the hole for the head of the screw smaller so that it does not touch the edge of the door when it is opened and closed. This will make it much easier to tighten the screws after reinstalling hinges.

After you have reinstalled the hinge, be sure to coat it using a dry lubricant to help keep it from getting stuck in the future. You can use products such as PB Blaster and Liquid Wrench. You should apply a thin coat and wait for approximately 15 minutes to get into the barrel of the hinge.

Refinishing the Hinges

If you are not ready to replace the hinges on your door, you could make a few minor repairs. The first step is to check that the screws securing the hinge plate to the frame and door are tight. If they're loose, tighten them using a screwdriver or power drill. Be careful not to tighten the screws so tight that they begin to create gaps at the trim joints or, even more damagingly cause threads to be stripped.

If the problem is the hinge plates are separating they can be reattached to the plates by applying wood glue on the back of them and then inserting wooden dowels or toothpicks in the holes. The dowels or toothpicks provide a solid base for the screws and help prevent the plates from shifting when you drive them into position. Let the glue dry before you can reattach your hinge.

Another reason for hinges that are loose is that screws are worn out or missing. This problem can be fixed by replacing the screws. Be sure to use a drill bit that matches the size of the screw hole in order to avoid drilling into other parts of the jamb or hinge.

After you've reattached your hinge shut the pvc door hinges and check the gap between the door and the frame. It should be about the thickness of one nickel all around, or less if there's an existing gap that was caused by a previous door that hung improperly. This shouldn't be a problem as long as the hinges are correctly installed.

If you find that the hinges remain loose, you can try adding the thicker shim of the hinge between the window hinge replacement plate and the mounting surface to add a little extra space. You can also remove the hinge pin, then pound it down with a heavy hammer to tighten it or use the hinge of a different type. You can also lubricate your hinges using mineral oil or jojoba to reduce friction and hold them in their place. Periodically lubricating your hinges can help keep them from becoming stiff or squeaky and can also extend their life.

Cleaning the Hinges

The friction created by the hinge's constant motion attracts dust particles. These particles can become stuck and build up in the moving parts of door hinges if they're not regularly cleaned and lubricated. The hinge will get stiff and creaky, and its appearance can rapidly change. Regular cleaning, lubrication and inspection can help preserve the quality of a hinge on a door hinge repairs and ensure its proper operation.

Check the hinges for rust accumulation. If the corrosion has reached the point of destroying surface of the hinge barrel or screw holes, you'll have to replace the hinges. If you are able to save the hinges, first brush away loose rust using steel wool and wire brushes. Then, apply a commercial rust remover or a homemade solution such as lemon juice to the hinge. Let the solution that removes rust remain on the hinges for several minutes to penetrate and dissolve any remaining rust.

If you don't wish to spend the cost and time to replace hinges, tightening the screws can restore the hinges' functionality. It is possible to add dowel or shim made of wood to the hinge in the event that the screws have been degraded. Dowels made of wood are square pieces made of wood in the shape of rods which are available in different sizes and lengths. They are available at home improvement centers as well as woodworking supply and craft shops, or on the internet.

You can also create a shim from a piece metal or plastic depending on the type hinge you are using. To make a dowel, cut a piece of wooden dowel or other sturdy material to the desired size. Then, dip a dowel in carpenter's glue and insert it in the hole. The glue will hold the dowel securely in place.

Before cleaning the hinges put down a piece of paper cloth or towel to shield your flooring from spills. After you have protected the area clean the hinges with a soft sponge or a cloth dipped into mild cleaner to eliminate dirt and grime. You can also remove tarnish, dirt, and grime. You can use a toothbrush or small brush to get into difficult-to-reach areas in crevices or tight areas.