• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

UPVC Replacement Door Handles

The handles on your doors get worn out over time and will need to be replaced. When replacing them, it is important that the new handles match the exact dimensions of the previous handle.

The three measurements you need to examine are the top screw position the lever and key hole dimensions. Use the size guide to aid you.

Inline Lever/Lever

A lever door handle is a modern handle that can be put in on doors that are new or replacement. This kind bifold door handle replacement handle is offered in a wide range of designs and finishes. This handle is offered by several manufacturers including Avocet ERA Fullex Hoppe Mila Millenco Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The door handles made of uPVC/Composite are made of robust materials and are suitable for multi point lock doors that require a strong design. The replace window handles are inline and operate with the same spindle as well as screw fixings so they can be easily fitted to doors made of uPVC/Composite, either new or old.

The spring lever design allows the handle to be positioned and angled for comfortable operation and is suitable for all users. The handle has been tested for endurance up to 200,000 cycles, this will ensure the quality of the finish and the performance of the handle over time. The sprung lever is also adjustable to fit a broad range of locks. This is especially useful for doors with narrower frames, where the cylinder is further back. A shorter lever can be used for doors that have a latch that can be activated with the thumb located on the inside.

Lever Pad

A Lever Pad door handle made of upvc functions differently to the lever type handles on doors. These handle types can either operate from a single spindle (inline) or independently from each side by using two offset spindles or inline (pad). They are usually employed on UPVC doors with double glazing. They come in a range of finishes and variations.

The handles are available in a variety of finishes, including White, Chrome and Gold. The finish is in line with BS EN 1670:2007 Grade 5 and is also resistant to corrosion, which gives the handle a high degree of durability and performance for the intended use.

All UPVC handle lever pads come with a spindle, screws, and can be fitted on a uPVC door. The backplate fixation centres of 211mm permit a larger handle, which is usually a benefit when replacing a damaged or old multi-point door lock mechanism. These handle levers have a spring, which solves the problem of door handles that sag out of the horizontal position when they are not being used.

When choosing the replacement UPVC handle and spindle it is crucial to match the PZ dimensions of the multipoint lock as well as the uPVC door. This measurement is often referred to as the 'handle centre' or 'cylinder centres which is a crucial aspect in ensuring that you have the right handles.

When you have the right PZ size, you'll need to ensure that the lever pads and push pads are in a suitable shape to fit the American with Disabilities Act (ADA) compatible handles you need for your doors. These are typically of a round or square shape with an internal lever and an external push pad.

Most of the UPVC lever pads that we offer are sprung, which means that they return to their horizontal position when they are not in use, rather than hanging out and possibly sticking in the frame. This keeps draughts out of the property. The majority of UPVC lever pad handles come in both left and right handed models which allows them to be put on either side of the doors.

Euro Cylinder

Cylinder locks can be found on uPVC and other kinds of doors. The cylinder lock is operated by using a key that unlocks the cylinder's casing. This reveals pins that can be aligned to the pins in the lock, allowing them to rotate the camera that rotates, opening the door. Euro cylinders are available with up to six pins. External and internal doors require different levels of security.

The selection of a cylinder is crucial. It is based on the amount of use your doors and handles receive. Doors that are external, for instance, should be fitted with cylinders that are more secure while internal doors can be secured with a standard cylinder. Additionally, certain cylinders are available with extra features that can improve security, for instance anti-drill or anti-bump features.

To ensure that the euro cylinder is of the right size for your door, it must be measured correctly. The cylinder should be measured from the hole for fixing screws in the middle to the other end of the cylinder and the thumb turn if you have one. If you cannot measure using the lock in its position, you can take it out of it. A cylinder that protrudes beyond the handle and escutcheon might be vulnerable to attacks, such as snapping locks, therefore it is essential that it is not too long.

Most modern cylinders are constructed with anti-drill and bump resistance features built into their design. These are designed to reduce the chances of an attack by causing the cylinder to rotate in an opposite direction. This can help deflect the attack and protect your doors.

There are cylinders that are made to withstand snapping. This is an increasingly common method of attack on cylinders, where the break line inside the lock is targeted by a tool that is specially designed to break the front of the cylinder and allow the door to open. This is a much faster and more convenient method of gaining access than using the use of a multipoint locking system. It also leaves less evidence of the burglary which could delay insurance claims.

Spring Cassette

This spring cassette is located in the base plate of the door handle. It is a spring-loaded solution to bring your multipoint lock handles to their original position after using. In the past, a lot of handles did not have a spring integrated into them, and without it they tend to droop or 'drop' once the locking mechanism is removed. This simple feature is among the best ways to correct this, and is an effective way to keep your doors made of upvc from getting stuck in the open or closed position, since they aren't always simple to close manually.

These spring cassettes are specially designed to be used with multipoint locks sprung, they will not fit non-sprung multipoint handles. You will require a bespoke hole cut into your backplate to allow these to fit (please look at the image for a technical diagram). They are a replacement for existing broken or missing cassettes within the backplates of door uvpc window handles of numerous brands of uPVC doors. They are sold as one unit. They have a square-cut out that is able to accommodate an 8mm shaft.

These spring cassettes are an excellent value-for-money way to fix the problem of door handles that are sliding patio door handle replacement. They are simple to install and will prolong the lifespan of your uPVC doors. Please contact our team for more information about our wide range of uPVC accessories and spares. We are on hand to help and happy to offer expert advice.