• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Glass Window Repair

Professional window repairmen are able to maneuver large glass panes from a height above the ground. They follow strict safety protocols and often work under extreme weather conditions.

Wearing protective clothing, cut off the metal glazing points as well as the glazing putty by using a utility knife. A heat gun can help soften and remove the old putty.

Replacement

It's tempting to fix the window glass instead of replacing it if panes break. It is cheaper to replace windows and it can also help you prevent other problems in your home's efficiency. Consider the type of glass that is broken to determine whether it's a temporary fix or if a long-term solution is required.

The first step to repair a broken window is to remove the frame, or sash, and lay it flat on a work table. Wearing eye protection, gently move around and pull out any shards remaining in the window pane. Then, use a utility knife to remove the glazing compound as well as the glazing points that hold the glass in the position. Make sure you keep an eye on these components and their locations so that they can be replaced later.

After you've removed the frame and sash you can start preparing to replace the glass. Make sure you check the opening of the frame is the proper size for the replacement window. Measure both sides of the opening, and then subtract 1/8 inch from each measurement to allow space for expansion and contraction of the frame and glass. Afterwards, purchase double-strength glass cut to these exact measurements. It is also an excellent idea to buy enough new glazier's points or clips to be placed every 6 inches around the window pane.

If the manufacturer is accountable you should contact them and make a claim. After the new glass has been erected, it is important to cover it with a thin layer glaziers compound. After drying the compound and dry, you can paint it to match the rest of the frame.

If you have a crack that is more than an inch, cutting an arc of a razor blade just beyond the crack could help stop it from spreading further. This method isn't foolproof, but it can slow the development of the crack until you can take more permanent measures.

Repair

Professional window installers have the appropriate tools and know how to work with various types of glass. They are able to dispose of waste in a safe manner which means they are less likely than other people to leave behind a mess that could inflict harm on family pets or family members. They're also used to working with different window types, and they may be capable of identifying issues that aren't apparent to the uninitiated homeowner.

Wear safety goggles and gloves prior to beginning the process of repairing window cracked glass. A small crack could cause glass shards to fly and could pose a danger to anyone in or around the home. It's also important to determine what caused the crack in the first place, since it can help prevent future issues.

Start by making a two-part epoxy mixture. They typically are a 50/50 mixture of resin and hardener and must be mixed quickly. Once the mixture is ready, apply it to the glass crack and let it dry. It should take only about a few minutes, but you must work quickly because the mixture is very thick and drys quickly.

After the epoxy has dried, you can take off excess epoxy with a putty blade. The next step is to scrub the cracked glass. If you do not clean the area in a proper manner, the leftovers could cause further damage to your glass. Use a putty blade to smooth out the compound around the edge of the window and match it to the frame of wood.

To make a more durable option, consider using a plastic covering. A trash bag that is heavy-duty or tarp is ideal, however you can also use masking tape to cover the glass. This will stop the crack from spreading and will also keep water, wind and insects out.

You can create an interim solution in the event that you are unable to access the window in a timely manner. Apply a small amount of silicone sealant to the edge of the broken glass. It won't seal the gap between the frame and the glass completely, but it will hold the fracture until you can fix it.

Repainting

If your windows with glass are old, you may need to paint them. This is a low-cost alternative to replacing windows, and it can give your home a new look. Before painting, upvc ensure that the surface is clean. Wash the window with water and soap or ruby alcohol to get rid of oil smudges and other traces which can hinder the paint from adhering. You should also wear rubber gloves while working on glass to prevent the transfer of your own oils onto the glass surface. Also you should apply several thin coats of paint instead of a single thick layer. This will allow the paint to last longer and keep your windows looking even and smooth.

Make sure you have the appropriate tools in your arsenal if you plan to repaint glass windows. You'll require a brush or sponge, painter's tape toothpicks, a ruler and a few other tools such as a rag or paper towel. You'll also need the brushes and paint you'll use for the project in your possession. Be sure to adhere to the manufacturer's guidelines and have plenty of patience because it may take awhile for the paint to dry.

If you are using solvent-based paint, make sure that the area in which you work is well-ventilated. This will reduce the chance of breathing in toxic chemicals and allow the paint to dry quicker. It is also important to ensure you have a mask to protect yourself for any spray paints you apply.

It is necessary to clean the glass window thoroughly with warm water and soap before you paint it. Make use of soap and warm water to thoroughly clean the glass window. Then, rub alcohol on any oil or grease residues that could interfere with the adhesion of the paint. Make sure that the windows are dry before you start coating them.

If your glass windows are energy-efficient dual pane windows, you might be able to make a claim with the window manufacturer or dealer who sold them to cover any repair double glazed windows or replacement costs. This is especially true if you have experienced numerous issues with broken glass or condensation and the windows are covered under warranty.

Sealing

There are several ways to address the issue, regardless of whether you have an old double-pane window that has cracks in the seal, or if you have a newer insulation unit (IGU) that has experienced fogging. The most expensive option is to replace the insulated unit and frame, but it may be required if fog or condensation is causing energy loss. Other options include replacing the existing IGU with a single pane or repairing it by drilling a small hole through the bottom of the unit and then filling the solution with anti-fog.

You can also seal the gap between the window frame and the sill or threshold by using a felt strip vinyl v-strips, or door sweep. Felt is affordable and can be glued, nailed or stapled to the frame, but it does not provide a lot of protection from moisture. Vinyl weather stripping v-strip is durable and easy to install however it can be expensive and is usually used for areas that are subject to abrasions that are high. Door sweeps are able to be easily nailed in place and are cheap. However, they provide very little or no protection between the threshold and air.

To repair a cracked window seal first, employ a putty knife to remove the old caulk. Wearing gloves and eye protection take care to remove the glazing points -- small fasteners that hold the glass to the frame's recess using sharp and pointed edges. Once you have removed the glazing points, scrub the grooves and sand the wood smooth. Wipe off any sanding traces and then seal the unfinished wood with a linseed oil based paint or clear wood sealer.

A caulking knife or putty can be used to apply traditional glazing putty, but using a knife will give an easier application and a better seal. Choose a putty specifically for glass, since it will be more durable and adhere better.

Apply a thin bead of the putty to the inside edge of the frame where it meets the glass. Slide the window into frame so that scribed line on glass lines up with edge of frame. Apply pressure on the glass to force the putty and glass into an elongated seal. Smooth the compound with gloves and get rid of any drips or caulk that were applied incorrectly before it has dried.