• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

The change of your door lock is an easy and inexpensive way to increase the security of your home. This process isn't for all. It requires a certain amount of patience and expertise.

It is necessary to replace the cylinder that is inside the knob's body. The cylinder recognizes the key once it's placed into the lock.

Remove the old lock

The first step to replace the door lock is to get rid of the old lock. This is a relatively simple procedure, but there are some things to be aware of. Make sure your new lock fits the door. This will ensure that it fits properly and does not leave a gap around the deadbolt plug or latch.

After you have removed the latch plate look for two screws or bolts on the inside of the casing that connect the casing and two halves of the lock together. Remove these screws using the help of a screwdriver, and then remove the lock out of the door. If you have a mortise Upvc window locking Mechanism Repair mechanism there is a set screw that holds the handle to the spindle. Use a screwdriver to unscrew this screw, then remove the doorknobs.

It is also recommended to remove the latch and deadbolt plug from the hole in the door jamb. Install your new lock. If you are replacing a mortise lock, you should also determine the distance between the double glazed window lock repairs case and the door's edge to ensure that the new lock will fit.

You might want to change your double glazed window lock repair for various reasons, including when you suspect that someone else has the key, or if you've a new roommate. In any event, you could save money by removing the lock yourself rather than paying an expert to do it. It's much simpler than most people imagine and can be done in a matter of a few minutes.

Remove the trim and handle of your door. Then, you can pry the trim loose with a flat screwdriver. You should be able to twist off the majority of it, and in certain cases, the handles might come off entirely. Then, look for a tiny pinhole on the interior side and insert a straightened paper clip into it. This will activate the release mechanism and allow you to take the handle from the door. Next, examine the inside of the lock for a small tab, and then press it using a screwdriver that is flat. After the spindle has been removed, you are able to remove the housing and the cylinder.

Selecting a new lock

There are many options to choose from when it comes to selecting the right lock. Take a look at the various types of locks and choose one that is in keeping with the style of your door. Take into consideration the backset (the distance between the edge of the door and the center of the lock hole) and the cross bore (small hole along the edge of the door frame). Also, be sure to choose a lock that will be able to fit the door's thickness and swing.

The American National Standards Institute and BHMA have graded the majority of locks for doors to give you an idea of their durability and how difficult it is to pick them up or disable them. A grade 3 lock may be perfect for a quiet apartment building in a rural area, whereas a lock of grade 1 may be more suitable for a busy street near an open-air storefront.

Most smart door locks require a digital code to open. If you're worried about hacking or other security concerns, consult with an expert locksmith or your local police department to get advice.

Replacing the cylinder

If your door lock cylinder is broken or damaged you can repair upvc window lock it in just a few minutes using a simple DIY project. It is important to select the appropriate cylinder and follow all instructions. First, remove the knob or handle if it is present. Then, using a screwdriver, unscrew the trim that surrounds the lock cylinder. Once the trim has been removed, you can access the screws that hold the cylinder in place and remove them using a flathead screwdriver. The cylinder is then gently removed out of the door.

Make sure you measure the length of the new cylinder prior to installing it. Measure the distance from the center to the right and left sides of the cylinder with a tape measure. Buy a new cylinder that has the same measurements. This will stop cylinders from snapping when the door is kicked or the key becomes stuck inside.

Place the replacement cylinder inside the door and then turn the key. This will ensure that the cylinder is in alignment with the carrier, which is normally located on the outside of the lock. After that, you can loosen the set screw that should be just a few turns inside the head. Also, you will need to loosen the screw on the door's edge which secures the case if there is one.

After removing the lock cylinder, you can replace it with the new lock by sliding the new cylinder into the case and tightening the set screw. You must also install the piece that connects the cylinder to the stem of the lock indicator, which you can do by removing three small tabs on the back of the cylinder using needle-nose pliers. Attach the bracket that is smaller to the cylinder's back. Then, you should reinstall the strike plate and latch plate, along with the retaining rings attached to the top of the lock cylinder.

Installing the new lock

If you're replacing an old lock, start by measuring the width of the door. The majority of residential locksets have a thickness of 3/8 inch to 1 3/4 inches. If your door is thicker you will require a door kit that is thick and includes longer screws, longer tail pieces (for door knobs) or spindle extension (for deadbolts).

Most locks come with a detailed instruction manual to guide you through the installation of the new hardware. Take the time to read the instructions before beginning the process to make sure that you've followed all the steps. The booklet will give you an idea of how much skill is required to complete the task. It is possible to ask a person who has experience changing locks for assistance if you are changing a lock the first time.

It's a great idea to tape the openings in the old hardware prior to installing the new lock. This will keep the screws from falling out of the holes and will protect any tiles you might have installed in the area. This will also protect your tiles from any damage caused by dirt, rust and grime. SECURAM Touch comes with a piece of painter's tape designed to be used to protect your painter's tape, but you can also use gaffer's tape or masking tape when you have it.

After you have removed the screws that hold the lock's inner half to the exterior then pull the lock straight away. It's important to do this quickly to avoid the lock from closing itself in a way that could end up damaging the mechanism.

Install the new latch bolt into the upper cross bore of the new lock, if it has one. Make sure to place it in the correct position, which is marked by an arrow. Next, fit the latch plate onto the bolt and screw it in place.

Screw the deadbolt to the jamb on the door. Check the deadbolt several times by throwing it to make sure it extends into the strike plate. Follow the instructions included with your electronic smart lock to program it. This requires downloading an application and registering your e-mail address, verifying your identity, and connecting to the wireless network in order to connect your device.