• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door Lock Change

Change of the door lock is an easy and inexpensive method to boost your home's security. This process isn't for everyone. It requires a certain amount patience and skill.

It is necessary to replace the cylinder that is inside the knob's body. The cylinder is responsible for recognizing the key when it is put into the lock.

Remove the old lock

The first step in replacing a door lock is to remove the lock that was previously in use. This is a relatively easy process, but there are a few things to remember. Make sure your new lock is compatible with your door. This will ensure that it fits snugly and does not leave a gap in the deadbolt plug or latch.

After removing the latch plate, you will need to look for two screws or bolts on the inside of the casing that are holding the casing in place with the two halves of the lock. Unscrew these with a screwdriver, then pull the lock out of the door. If you have a mortise locking, there might be a set screw at the base of the handle that binds it to the spindle. Take off the doorknobs by removing this screw using the help of a screwdriver.

Take the deadbolt and latch plug from the door jamb. Then, you can install your new lock. If you are replacing a mortise lock you must also measure the distance between the lock case and the edge of your door to ensure that your new lock will fit.

You might want to change your lock for a variety of reasons, for instance, when you suspect that someone else has the key, or if you've got a new roommate. In any case, you can save money by taking the lock off yourself rather than paying an expert to do it. It's much easier than you think and can be completed in a matter of a few minutes.

Begin by taking the handle and trim from the door. With a flat screwdriver, take off the trim. You should be able twist off the majority of it. In some instances you may be able to take off the handles completely. Next, look for a pinhole on the inside of the handle and then insert an unstraightened clip into it. This will activate the release mechanism and allow you to take the handle from the door. The next step is to look at the interior side of the lock to find a small tab, and then press it using a screwdriver that is flat. After the spindle is removed, you are able to remove the cylinder and the housing.

Selecting a new lock

You have many options when it comes time to pick the right lock. Think about the various kinds of upvc window locks repair and pick one that matches the design of your door. Think about the backset (the distance between the door's edge and the center of the hole for the lock) and the cross bore (small hole in the frame of the door frame). Also, make sure to choose a lock that will fit the door thickness and swing.

The American National Standards Institute and BHMA have graded most locks for doors to give you an idea of their longevity and the difficulty to pick them or disable them. A grade 3 Repair upvc window lock may be perfect for a quiet apartment building in the countryside, whereas locks that are grade 1 may be more appropriate for an area with a lot of traffic, such as an open-air storefront.

Most smart door locks require a digital key code to open. If you are worried about hacking, or other security concerns, consult an expert locksmith.

Replace the cylinder

If your door lock cylinder is damaged or broken it can be replaced in just a few minutes with a simple do-it-yourself project. The key is to choose the right cylinder and follow the steps that come with it. First, you must remove the handle or knob if it is present. Then using a screwdriver unscrew the trim that surrounds the lock cylinder. After the trim is removed, you can take off the screws that hold the cylinder in place using a flathead. The cylinder is then gently removed out of the door.

Before you install the new cylinder, you must make sure that it is the correct length for the door you are using. With a tape measure, measure the distance between the cylinder's center and its left and right sides. Then, buy an additional cylinder using the same measurements. This will help prevent cylinder snapping, which can happen when the door is kicked in or when the key sticks inside.

Insert the upvc replacement window locks cylinder in the door and then turn the key. This will ensure that the cylinder is in alignment with the carrier, which is typically located on the outside of the lock. You can then loosen the set screws which should be only a couple of turns into the head. If there is a screw on the exterior of the case that is holding the door, you will need to loosen it.

You can replace window lock the cylinder that was used to lock your old lock with the new one by slipping it into the case, and tightening the set screws. It is also recommended to reinstall the piece that connects the cylinder with the lock indicator stem that you can do by pulling up three small tabs on back of the cylinder using needle-nose pliers. Then, you'll be able to attach the second bracket to the back of the cylinder. You should then reinstall the strike plate and latch plate, as well as the retaining rings that are fixed to the top of the lock the cylinder.

Installing a new lock

Start by measuring the width of your door if you are replacing a lock that is already in use. Most locksets for residential use are designed to fit a door thickness of 1 3/8 - 3/4 inches. If your door is more thick you will require a door kit that is thick and includes longer screws as well as a longer tail piece (for door knobs) or spindle extensions (for deadbolts).

The majority of locks come with a detailed instruction manual to help you install the new hardware. Be sure to read the instructions thoroughly before beginning the process to make sure that you've followed all of the necessary steps. The guide will also give you an idea of the level of expertise required to complete the task. If you're replacing a lock for the first time, you might consider asking a more experienced friend for assistance.

It's a good idea to seal the openings of the old hardware prior to installing the new lock. This will prevent the screws from falling out of the holes and safeguard any tile you may have put in the area. It also shields your tiles from any damage caused by dirt, rust and grime. SECURAM Touch comes with a strip of painter's tape that is intended to be used to protect your painter's tape, but you can also use gaffer's or masking tape in the event that you have it.

After taking off the screws that connect the replacement window lock's interior to the exterior then remove the lock immediately. This must be done quickly to prevent the lock from accidentally closing and damaging the mechanism.

If your new lock is equipped with a latch bolt, fit the new latch bolt into the upper cross bore. Be sure to put it in the correct place as marked by an illustration on the faceplate. Then, slide the latch plate on top of the bolt and secure it in place.

Attach the deadbolt to the jamb on the door. Test the deadbolt a few times, throwing it around to ensure it is extending into the strike plate. Follow the instructions included in your electronic smart lock to program it. This involves downloading an application and creating an email address, confirming your identity, and then connecting to the wireless network to connect your device.