• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

UPVC Replacement Door Handles

The handles on your doors are worn out over time and need to be replaced. When doing this it is crucial that the new handles conform to the exact dimensions of the previous handle.

The top screw's location as well as the lever and keyhole size are the three measurements you have to check. Use the size guide to help with this.

Inline Lever/Lever

A lever door handle is a modern handle that can be put in on replacement door handles or new doors. This kind of handle is available in a variety of designs and finishes. This handle is offered by several manufacturers including Avocet ERA Fullex Hoppe Mila Millenco Yale.

Fab and Fix Windsor Inline Sprung Lever Door Handle

The handles of uPVC/Composite are constructed from robust materials, and are perfect for multi-point lock doors that require a robust design. The handles are inline and run off the same spindle and screw fixings. They can be easily fitted to doors made of uPVC/Composite, either new or old.

The handle can be placed and angled to accommodate the needs of all users. The handle has been tested to 200 000 cycles. This helps to ensure that the quality of finish and performance over time. The sprung lever is adjustable to fit a broad range of locks. This is useful in doors that are narrower, where the cylinder is further back in the door. A shorter lever can be used on doors with a latch which can be operated with the thumb located on the inside.

Lever Pad

A Lever Pad upvc door handle operates differently to the lever type handles on doors. These handle types can either use a single spindle (inline) or independently from each side using two inline or offset spindles (pad). They are generally employed on UPVC double glazed doors. They come in a variety of styles and finishes.

The handles are available in a variety of finishes, including White Chrome and Gold. The finish is BS EN 1670 Grade 5 and is resistant to rust. This gives the handle for double glazed window an outstanding performance and durability for its intended purpose.

All of the upvc sliding door handle handle lever pad styles are supplied with the spindle and screws which allow them to be installed on an existing or new uPVC door. The backplate fixation centers of 211mm allow for a bigger handle, which is usually an advantage when replacing an old or damaged multi-point door lock mechanism. The handle levers come with a spring, which solves the issue of handles for doors that slide out of the horizontal position when they are not being used.

It is essential to ensure that the PZ dimensions of both the multipoint sash lock door handles as well as the uPVC doors when choosing the replacement UPVC spindle and handle. This measurement may also be referred to as 'handle centres or cylinder centre'. It is important to match the right handles.

When you have the right PZ size you will then be required to make sure that the lever pads and push pads are in a suitable shape to fit the American with Disabilities Act (ADA) compatible handles you require for your doors. These are typically round or square with an internal lever and an external push pad.

Most of the UPVC lever pads we sell are sprung, meaning that they return to their horizontal position after not in use, instead of hanging out and possibly securing in the frame. This prevents draughts from entering the property. The majority of UPVC lever pad style handles are available in left and right handed versions that allow them to be installed on either side of the doors.

Euro Cylinder

Cylinder locks are usually found on uPVC doors, but they can also be used on other types of doors. They operate by using a key that unlock a cylinder case that then reveals pins which can be aligned with those in the lock body, allowing them to turn an revolving cam, opening the door. Euro Cylinders can be fitted with up to six pins, with internal and external doors generally requiring different levels of security.

The choice of cylinder is essential. It is based on the type of use your doors and handles will receive. For example, external doors should be fitted with an extra secure cylinder, whilst internal doors can be secured using a standard cylinder. Some cylinders have extra features that can improve security, such as anti drill or anti bump properties.

A euro cylinder should be properly measured to ensure it is the correct size for your door. The cylinder must be measured from the screw hole at the center to the ends of the cylinder. This includes the thumb turn, should there be one. It is best to do this while the lock is in place, but if this is not feasible, you can take it off and remove it to measure. It is essential to not have a extension of the cylinder beyond the handle or escutcheon. This can make it vulnerable to lock snapping attacks.

The majority of modern cylinders have been constructed with anti-drill and bump resistance features included in their design. They are designed to minimize the chance of attack by forcing cylinders to rotate in a different direction. This will help to stop the attack and ensure your doors are secure.

There are also cylinders made to resist snapping. This is a growing kind of attack on cylinders where the break line inside the lock is targeted using a special tool to snap off the front of the cylinder and allow the door to be opened. This is a faster and more convenient method of gaining access than using a multipoint locking system. It also leaves no evidence of the break-in which can delay insurance claims.

Spring Cassette

The spring cassette is located inside the base of your door handle backplate providing a sprung solution to return the multipoint lock handles back to their normal position after use. Previously a lot of handles of this kind did not have a spring integrated into them, and without it they can droop or drop once the locking mechanism has been disengaged. This component is the best way to address this issue. It also prevents your upvc door from becoming stuck in either the closed or open position since they are difficult to close manually.

These spring cassettes are specifically made for use with sprung multipoint locks They will not work with multipoint handles that are not sprung and you will need to have a hole specifically cut in your backplate in order for them to fit (please check the image for a technical diagram). They are a replacement for existing broken or missing cassettes in the backplates of door handles of numerous kinds of uPVC doors. They feature a square cut-out that allows for an 8mm spindle to be used and they are supplied individually.

These spring cassettes offer a great value solution to the issue of sagging door handles. They are easy to fit and will extend the lifespan of your uPVC doors. For more information about our selection of uPVC spares and accessories contact us today. in touch with our team. We are on hand to assist you and offer expert advice.